UK
AU
B1786-00

This fault code indicates the resistance of the driver's front airbag stage 2 (high-power deployment stage) squib circuit exceeds the normal threshold set by the SRS ECU (standard value is typically 1 — Atto 3

Safety System

This fault code indicates the resistance of the driver's front airbag stage 2 (high-power deployment stage) squib circuit exceeds the normal threshold set by the SRS ECU (standard value is typically 1.0–2.0 Ω; threshold is generally 2.5 Ω).

The dual-stage airbag system triggers in stages based on collision severity, with stage 2 providing greater inflation power during a severe collision.

Excessive resistance indicates high resistance in the squib circuit, which may cause the ECU to detect an open-circuit risk.

This prevents or delays stage 2 deployment during a severe accident, significantly reducing driver protection.

This is a hard fault that does not clear automatically and illuminates the airbag warning light on the instrument cluster.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Internal fracture in the Qin EV300 clock spring caused high resistance.

✓
The airbag warning light on the instrument panel stayed on. Retrieved DTC B1786-00. Measured the airbag module resistance; readings normal. However, when testing continuity between the upper and lower terminals of the clock spring, resistance fluctuated between 2.8-5.0Ω with intermittent open circuits when rotating the steering wheel. Removed the clock spring and found micro-fractures in the internal flat ribbon cable from long-term steering wear. Replaced the clock spring (part number: KJ-3472910). Resistance returned to normal and the fault cleared.
BYD DTC AI Analysis

Flood-damaged vehicle with oxidised and corroded airbag connector

✓
Qin 80 owner reported the airbag warning light illuminated after driving through standing water in heavy rain. The diagnostic tool displayed DTC B1786-00. Inspection revealed water staining and green copper corrosion inside the yellow connector beneath the steering wheel. Oxidation on the pin surfaces caused contact resistance of 3.2Ω. Cleaned the connector with precision electronics cleaner, polished the pins with fine sandpaper, applied conductive protective grease and reconnected. Resistance returned to normal and the fault code did not return after clearing.
BYD DTC AI Analysis

Internal Stage 2 squib in airbag module degraded

✓
2017 Qin 100, 80,000 km. SRS warning light suddenly came on. Disconnected the airbag module and measured second-stage igniter resistance at 4.1 Ω — out of spec. Determined the internal igniter pyrotechnic charge had absorbed moisture or the pins had oxidized, increasing resistance. Replaced the driver airbag assembly (gas generator and igniter). Resistance returned to 1.4 Ω and the system passed the self-test.
BYD DTC AI Analysis

Loose wiring harness connection causing intermittent high resistance

✓
Airbag warning light illuminated intermittently, sometimes clearing after restart. Diagnosis revealed intermittent DTC B1786-00. Inspection found the internal locking tab on the clock spring-to-body harness connector loose, preventing the connector from seating fully; vehicle vibration caused contact resistance to fluctuate. Re-secured the wiring harness clip to ensure the connector locked completely. Fault has not recurred.
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.