UK
AU
C057900

DTC C057900 indicates the IPB (Integrated Power Brake) electro-hydraulic control module detected a short to ground in the brake booster motor temperature sensor signal circuit — Atto 3

Braking System

DTC C057900 indicates the IPB (Integrated Power Brake) electro-hydraulic control module detected a short to ground in the brake booster motor temperature sensor signal circuit.

Typically integrated inside the electro-hydraulic brake booster, this temperature sensor uses a negative temperature coefficient (NTC) thermistor to monitor the booster motor operating temperature in real time and prevent overheating damage.

The ECU logs a short to ground fault when the sensor signal voltage remains below the calibrated threshold (typically <0.5V) for longer than the set time (e.g., 200ms).

This fault triggers the IPB system to enter a degraded safety mode, which may reduce or eliminate brake assist (hard brake pedal), disable the energy recovery system, restrict ABS/ESC functions, and illuminate multiple brake system warning lights.

Continued driving under extreme operating conditions may cause a complete loss of brake assist, posing a serious safety risk.

Workshop practice on certain vehicle models indicates this DTC may also involve a short to ground in the brake switch signal circuit.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

BYD Qin Pro DM brake switch internal contacts oxidised

✓
Symptoms: Vehicle failed to enter READY state (no HV activation). Cluster showed "Check Brake System" and "Check ESP System". Brake lights stayed off when pressing the pedal. Scanner read code C057900 (brake switch signal abnormal). Vehicle started occasionally, but cruise control did not work. Diagnostic process: 1. Connected VDS2000/3000 and checked codes. Only C057900 present; no related faults. 2. Consulted the wiring diagram. Brake switch uses four wires (dual signal): pin 1 constant power (B+), pin 2 ground, pin 3 signal 1 (normally open), pin 4 signal 2 (normally closed). 3. Disconnected the brake switch connector. Pin 1 measured 12V; pin 2 grounded normally. Reconnected the connector and checked signal pins. When pressing and releasing the brake pedal, pin 3 stayed at 0V (no change) and pin 4 stayed at 12V (no change). 4. Removed the brake switch. Internal contacts were severely oxidised and burnt, preventing the signals from conducting. Solution: Replaced brake light switch assembly (part number: 3720A-XXXXX, verify for your model year). Cleared codes and test drove. Vehicle now enters READY normally, brake lights work with the pedal, fault resolved.
Original source ↗
BYD DTC AI Analysis

BYD Song PLUS brake switch installation clearance improper

✓
Symptoms: ESP warning light illuminates intermittently while driving, accompanied by flashing oil pressure warning light (false alarm). Fault code: C057900. Owner reports: (1) AUTO HOLD function fails intermittently; (2) When releasing the brake to pull away, vehicle occasionally surges (sudden power delivery); (3) Cruise control cannot be set. Diagnosis: Connected scan tool to monitor live data. Brake pedal status signal fluctuated rapidly between "depressed" and "released" without driver input. Physical inspection revealed approximately 2 mm clearance between brake switch and pedal plunger (specification: 0–1 mm). Because the switch was not fully compressed, road vibration caused poor contact, creating an intermittent signal the ECU flagged as abnormal. Repair: Loosened brake switch locknut, threaded switch body two turns toward pedal to close gap, confirmed plunger fully depressed at pedal rest position (faint click audible), then tightened locknut. Cleared fault codes and completed 50 km test drive; fault did not return.
Original source ↗
BYD DTC AI Analysis

BYD Yuan EV535 brake switch wiring harness connector pin backed out

✓
Vehicle starts, but the instrument cluster continuously displays "Check Brake System" with DTC C057900. Notable symptoms: When depressing the brake pedal, the high-mount stop lamp lights up, but the side brake lamps do not (or vice versa), and the vehicle intermittently cannot shift out of Park. Diagnosis: 1. Checked the brake switch fuse (F2/23 10A) — normal. 2. Disconnected the brake switch harness connector (located at the upper brake pedal, black 4-pin plug). Found pin 3 (signal wire) backed out approximately 3mm, not making effective contact with the switch terminal. 3. Found the pin retention latch broken, causing poor contact. Further inspection revealed a wiring harness manufacturing defect in this model batch; the pin was not properly crimped. Repair: Extracted pin 3 using a terminal release tool, re-crimped the terminal, and secured the harness to the body with cable ties to eliminate strain. Applied conductive paste to the connector and wrapped it with waterproof tape to prevent recurrence. Installed an improved brake switch (with harness assembly). Fault completely resolved.
Original source ↗
BYD DTC AI Analysis

BYD Tang DM brake switch signals not synchronized

✓
Symptoms: Starts normally when cold. After about 10 minutes of driving, the dash shows "Braking System Fault" with DTC C057900. Also: the EPB won't auto-release (must release manually), and regen drops out suddenly during deceleration. Diagnostic Process: 1. Checked brake switch dual signals (primary and redundant) in live data. When cold, the two signals showed opposite logic (normal: one at 0V, one at 12V; abnormal: both at 12V or both at 0V). 2. Fault appeared after warm-up. Determined the brake switch has poor internal thermal stability; both contact sets stick simultaneously when hot. 3. Switch power and ground checked normal. Ruled out wiring. Confirmed internal switch fault. Solution: Replaced the OEM brake light switch (Tang DM requires the four-wire dual-signal type—do not use a standard two-wire switch). After replacement, ran "Brake System Calibration" with a scan tool (some models require this) to learn the pedal free-travel position. After calibration, both signals resumed opposite logic and the DTC cleared.
Original source ↗
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.