B1712

DTC B1712 indicates the SRS (Supplemental Restraint System) detects a 0 ohm resistance in the right curtain airbag firing circuit (located in the roof side rail, protecting front and rear occupant heads) — Atto 8

Safety System

DTC B1712 indicates the SRS (Supplemental Restraint System) detects a 0 ohm resistance in the right curtain airbag firing circuit (located in the roof side rail, protecting front and rear occupant heads).

This indicates a hard short circuit in the firing circuit (short to ground or short to power), not an open circuit.

Normal airbag inflator resistance ranges from 2.0-3.0 ohms (typical value approx. 2.3Ω).

A 0 ohm resistance allows current to bypass the inflator bridge wire.

This prevents proper airbag deployment during a collision or creates a major safety risk of unintended deployment.

The SRS ECU continuously monitors all firing circuit impedances in real time using a highly sensitive Wheatstone bridge circuit.

If the ECU detects a resistance below the safety threshold (typically <0.8Ω), it sets this DTC, illuminates the airbag warning light, immediately disables the right curtain airbag and related coordinated protection strategies, and enters safety protection mode.

4
Cases Logged
BYD DTC AI Analysis

BYD Yuan EV right-side curtain airbag inflator internal short circuit fault

A 2019 BYD Yuan EV's airbag warning light illuminated on the dashboard while driving. Read the DTCs with VDS and found B1712 (right side curtain airbag resistance 0), with freeze frame data showing 0.1 Ω. Removed the right roof interior trim panel and inspected the curtain airbag connector; no damage or signs of water ingress were found. Disconnected the curtain airbag from the harness and measured the resistance across the igniter with a dedicated airbag tester. It measured 0.2 Ω (normal: 2–3 Ω). Diagnosed as a sintered short circuit in the igniter bridge wire. Replaced the right curtain airbag assembly (part number matched to the vehicle VIN). After reassembly, ran the SRS calibration procedure, and the fault was resolved.
Original source ↗
BYD DTC AI Analysis

Song MAX right side curtain airbag wiring harness chafed and shorted after accident repair

A 2019 Song MAX had a B1712 DTC after a third-party shop repaired right-side collision damage. Inspection found the shop had incorrectly removed and refitted the right C-pillar interior trim. The edge of a metal trim clip pinched the curtain airbag harness, damaging the insulation and causing a short to earth (0 Ω). Further inspection found missing harness retaining clips, allowing the wiring to chafe against the C-pillar metal frame while driving. Repair: Replaced the damaged harness section (from the junction to the airbag), performed a solder repair using the genuine wiring harness Repair Kit, rewrapped with high-temperature fleece tape and PVC corrugated tubing, reinstalled all harness retaining clips, and ensured >25 mm clearance from sharp metal edges. Fault resolved.
Original source ↗
BYD DTC AI Analysis

Tang DM: Water ingress, corrosion, and short circuit in right curtain airbag connector after wading.

A 2021 Tang DM logged fault code B1712 after wading through floodwater during a heavy rainstorm. Removing the right A-pillar trim and front roof headlining revealed the curtain airbag connector (located at the A-pillar-to-roof junction) had a degraded waterproof seal. Water had accumulated inside and the terminals had oxidised and blackened, causing an electrolyte short circuit between the positive and negative terminals (resistance measured at 0.5 Ω). Repair steps: Thoroughly cleaned the connector terminals with electrical contact cleaner and a fibreglass brush; blew out the wiring harness interior with compressed air to dry it; replaced the waterproof seal and connector housing; applied special conductive anti-corrosion paste (not ordinary grease) to the terminal surfaces; and wrapped waterproof tape around the connector. The repair cleared the fault. Check the sunroof drain tubes for blockages; these may have caused the leak.
BYD DTC AI Analysis

Qin Pro SRS ECU erroneously reporting zero resistance fault

A 2020 Qin Pro with no accident history had an intermittent airbag warning light on the dash. The scan tool read DTC B1712 as an intermittent fault. The right side curtain airbag resistance measured normal at 2.4Ω, and the wiring harness insulation was good. The fault occurred mostly in rainy weather. Inspection found the SRS ECU mounted beneath the centre console. A nearby AC evaporator drain pipe leaked, allowing occasional water into the ECU connector. This did not cause a direct short circuit, but it drifted the ECU internal monitoring circuit reference voltage, falsely reporting the curtain airbag resistance as 0Ω. The repair sealed the AC drain pipe, replaced the SRS ECU (requiring programming to match the vehicle immobiliser and VIN), and thoroughly dried the wiring harness connectors. The fault has not returned.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.