UK
AU
B17121A

DTC B17121A indicates the Supplemental Restraint System (SRS) detects a 0-ohm resistance in the right curtain airbag ignition circuit — Atto 8

Safety System

DTC B17121A indicates the Supplemental Restraint System (SRS) detects a 0-ohm resistance in the right curtain airbag ignition circuit.

Under normal operating conditions, the curtain airbag squib requires a specific resistance (typically 2.0–3.0 ohms, depending on the vehicle model).

A 0-ohm resistance indicates a short circuit.

Possible causes include an internal short in the curtain airbag module, a short between the positive and negative harness wires, or a short between connector terminals.

This fault causes the SRS control unit to determine the curtain airbag has deployed or has a circuit fault.

Consequently, the right curtain airbag fails to deploy during a collision.

This severely compromises side impact protection and constitutes a high-risk safety fault.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Case: Yuan Plus right side curtain airbag inflator replacement due to internal short circuit

✓
A 2022 BYD Yuan Plus (Atto 3) had the SRS warning light staying on constantly on the instrument panel. The technician retrieved DTC B17121A with a VDS2000 diagnostic tool. Following standard procedure, the technician disconnected the battery, removed the right-side headliner trim, and disconnected the right curtain airbag connector. Measuring the curtain airbag side with a multimeter showed 0.2Ω (normal value approximately 2.3Ω), indicating an internal short in the inflator. The technician replaced the right-side curtain airbag assembly (Part No.: SC2E-5824710), cleared the fault code, and performed a system self-test, resolving the fault. Analysis suggests that some curtain airbags from this production batch may have internal bridgewire welding defects causing micro-short circuits.
Original source ↗
BYD DTC AI Analysis

Qin EV connector corrosion and short circuit repair case after water wading

✓
A 2019 Qin EV's SRS warning light came on the day after driving through water during heavy rain. DTC B17121A stored as a current fault. Inspection found a blocked sunroof drain tube, allowing water to flow from the A-pillar into the right side curtain airbag connector (above the right front A-pillar). Disassembly revealed the connector held water and the copper terminals showed green corrosion with short-circuiting. After cleaning the terminals with anhydrous ethanol, drying the harness with an air gun, and applying conductive grease before reconnection, the fault temporarily disappeared. It returned one week later. Replacing the right side curtain airbag wiring harness connector and unblocking the drain tube permanently fixed the issue.
BYD DTC AI Analysis

E3 wiring harness damaged by aftermarket dash cam installation

✓
After installing a dash cam (power drawn from the headliner), a 2020 BYD E3's airbag warning light illuminated. Diagnosis revealed DTC B17121A. Inspection found that the installer had pierced the right-side curtain airbag harness sheath with a self-tapping screw while securing the dash cam wiring, shorting the positive and negative wires. After removing the screw, we found damaged insulation on both wires with copper cores touching. We cut out the damaged section, repaired it by soldering with special high-temperature flame-retardant TXL 18AWG wire, applied double-layer heat shrink tubing, and rerouted the wiring to avoid the curtain airbag area. Fault cleared.
BYD DTC AI Analysis

Right side curtain airbag wiring harness aging, chafing, and short circuit case

✓
A 2019 Qin EV with 120,000 km on the clock and no accident history: the SRS warning light suddenly came on. Scanning revealed DTC B17121A. Inspection showed the right curtain airbag connector was normal, and the airbag resistance measured 2.1 ohms. Tracing the wiring harness revealed that at the roof rail above the B-pillar, a cable clip had detached, allowing the harness to chafe against the body metal edge until the insulation wore through and shorted. Repair: replaced about a 30 cm section of the harness, re-routed and secured it to keep clear of sharp edges, and fitted an anti-chafing sleeve. Fault resolved.
BYD DTC AI Analysis

Case: ACU replacement due to false SRS control unit fault

✓
A 2020 Model E3 repeatedly logged DTC B17121A. The right curtain airbag resistance measured 2.2Ω (normal), and the wiring harness insulation was intact with no shorts. After disconnecting the airbag, we measured abnormally low resistance between the ACU output pins. We traced the fault to an internal right curtain airbag drive circuit issue in the SRS control unit (ACU), causing a false short circuit. We replaced the airbag control unit (VIN matching and system configuration required), then performed 'coding' and a 'collision output test' (simulation test) using the dedicated diagnostic scanner. This permanently cleared the fault.
Other Atto 8 Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.