UK
AU
B122A13

DTC B122A13 indicates an open circuit fault in the thermal management system coolant temperature sensor circuit — Seal 6 EV

Thermal Management System

DTC B122A13 indicates an open circuit fault in the thermal management system coolant temperature sensor circuit.

In models such as the BYD Qin EV300, this sensor typically mounts in the PTC (Positive Temperature Coefficient) water heater or the battery thermal management circuit.

It monitors coolant temperature to control heating power and battery thermal management strategies.

An open circuit means the ECU detects a continuously high sensor signal voltage (typically near the 5V reference voltage) and cannot acquire the actual temperature signal.

This fault forces the PTC heater into protection mode and halts operation, resulting in no warm air in the cabin.

It may also affect the battery preheating function, restricting charging speed or preventing charging in low-temperature environments.

In severe cases, the vehicle may trigger a thermal management system fault and enter limp mode.

5
Cases Logged
Real-World Cases
BYD DTC AI AnalysisFrom Chinese market (translated)

BYD Qin EV300 PTC heater inlet sensor open circuit causing no heating

✓
Vehicle came in with no heating and the thermal management system warning light on. Retrieved DTC B122A13. Live data showed PTC inlet temperature at -40°C (out of range low). Measured infinite resistance at the PTC heater inlet temperature sensor, confirming an internal open circuit. Since the sensor is integrated in the PTC water heater assembly, replaced the assembly. Fault cleared, heating returned to normal.
BYD DTC AI AnalysisFrom Chinese market (translated)

Wiring harness chafed through at the firewall penetration, causing an intermittent open circuit.

✓
The vehicle intermittently set DTC B122A13 on rough roads but operated normally on smooth surfaces. During a shake test, we found the firewall wiring harness clip had worked loose, allowing the harness to chafe against the metal panel edge. This wore through the insulation and partially fractured the copper cores, creating an intermittent high-resistance connection. We repaired the harness, rerouted the wiring, fitted a protective sleeve, and secured the clip. The fault has not returned.
BYD DTC AI AnalysisFrom Chinese market (translated)

Water ingress corroded the connector, causing poor contact.

✓
Drove after rain and developed a fault. Scan tool read DTC B122A13. Found the coolant temperature sensor connector in the engine bay had water residue inside. Oxidised and blackened pins caused high contact resistance, leading the ECU to misdiagnose an open circuit. Cleaned the connector with electrical contact cleaner, sanded the pins with fine sandpaper, applied conductive paste, and sealed the connection against water. Fault resolved.
BYD DTC AI AnalysisFrom Chinese market (translated)

Open circuit in battery cooling circuit temperature sensor limits charging power.

✓
During fast charging, power was only 20kW (normal 60kW) and the instrument cluster displayed a charging system fault. Read multiple thermal management DTCs, including B122A13 (battery coolant temperature sensor). Measured the battery pack coolant inlet temperature sensor and found an open circuit. This prevented the BMS from accurately determining battery temperature, so it limited charging current. Replaced the battery coolant temperature sensor and charging power returned to normal.
BYD DTC AI AnalysisFrom Chinese market (translated)

False positive due to internal circuit fault in AC controller

✓
Replaced the coolant temperature sensor, but DTC B122A13 persisted. Checked wiring harness continuity and power supply—both normal. Measured voltage from sensor signal wire to ground: 5V (normal should be a varying voltage). Suspected an internal signal acquisition circuit fault in the HVAC controller (thermal management controller). Replaced the HVAC controller and programmed the new unit. The DTC cleared and live data returned to normal.
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.