UK
AU
B164C12

DTC B164C12 indicates the airbag control unit (SRS ECU) detects an abnormally low-impedance connection between the front passenger seat belt pretensioner drive circuit and the vehicle power supply (B+) — Seal 6 EV

Safety System

DTC B164C12 indicates the airbag control unit (SRS ECU) detects an abnormally low-impedance connection between the front passenger seat belt pretensioner drive circuit and the vehicle power supply (B+).

The pretensioner is essentially an electric squib with a normal operating resistance of approximately 2.0-3.0Ω.

When damaged wiring harness insulation causes contact with a constant power wire, the ECU detects an abnormal voltage (approaching 12V/B+ voltage) instead of the expected open circuit or low-resistance state.

This fault triggers the SRS fail-safe mode.

The system disables the front passenger airbag and pretensioner functions to prevent injury from accidental deployment, and illuminates the airbag warning light to alert the driver.

Excessive short-circuit current also risks unintended pretensioner deployment or burning out the SRS driver chip.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Qin Pro DM seat rail crushed through the wiring harness, causing a short circuit.

✓
A 2019 BYD Qin Pro DM with 32,000 km came in with the SRS warning light on and DTC B164C12 stored. Inspection found that with the front passenger seat in its rearmost position, the seat rail mounting bolts pressed through the wiring harness corrugated tubing, causing the pretensioner power wire to contact the seat heating power wire (always live). The repair involved rerouting the harness, installing rubber protective sleeves for isolation, and repairing the damaged wires. Fault cleared.
BYD DTC AI Analysis

E2 BEV: Connector corrosion and short circuit after wading through water

✓
2020 BYD E2. A blocked sunroof drain caused water to accumulate on the passenger side carpet, which spread to the SRS connector beneath the seat. Removed the pretensioner connector and found electrolytic corrosion between the terminals, creating a conductive path between the power and signal terminals. Thoroughly cleaned the connector, flushed it with electronic cleaner, dried it, applied conductive protectant, and replaced the damaged wiring harness terminals.
BYD DTC AI Analysis

Qin EV aftermarket seat heater installation causing interference

✓
2019 BYD Qin EV set DTC B164C12 one week after an aftermarket shop installed seat heaters. Inspection found the installer had spliced the heating pad power wire into the cigarette lighter power circuit and routed the wiring along the factory SRS harness. Metal harness clips had pierced the pre-tensioner harness insulation. Repair: Removed the non-compliant aftermarket wiring, re-wired the seat heaters following the factory routing, repaired the SRS harness insulation, and restored the system.
BYD DTC AI Analysis

E3 pretensioner internal short circuit - replace assembly

✓
2020 E3 was involved in a minor rear-end collision (no airbag deployment). The SRS warning light then stayed on with DTC B164C12. Wiring harness inspection showed no faults. Pretensioner resistance measured 0.8 Ω with continuity to ground. Diagnosed as an insulation breakdown of the internal igniter in the pretensioner. Fix: Replaced the front passenger seatbelt assembly (including pretensioner), performed configuration coding and matching via VDS, and carried out crash sensor calibration.
BYD DTC AI Analysis

BYD Qin Pro petrol — SRS ECU false fault

✓
2018 Qin Pro petrol variant intermittently sets DTC B164C12. Inspected wiring harness: normal. Measured pretensioner resistance: normal. Monitored the ECU driver output with an oscilloscope and detected abnormal voltage spikes. Confirmed poor thermal stability of the internal driver chip in the SRS ECU. Solution: Replaced the airbag control unit, rewrote the vehicle VIN and configuration parameters, and performed system calibration.
Other Seal 6 EV Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.