UK
AU
B16C2-00

DTC B16C2-00 indicates the airbag control unit (SRS ECU) detected a critical fault during its internal self-check, forcing the system into fail-safe mode — Seal U

Safety System

DTC B16C2-00 indicates the airbag control unit (SRS ECU) detected a critical fault during its internal self-check, forcing the system into fail-safe mode.

This fault involves a hardware-level abnormality in the ECU internal microprocessor, non-volatile memory (NVM), power management module, or safety monitoring circuit.

The ECU sets this code upon detecting an internal watchdog reset, checksum verification failure, integrated acceleration sensor (MEMS) signal processing circuit abnormality, or safety communication interruption between the main and secondary CPUs.

In BYD Qin series vehicles, this fault prevents the entire airbag system (including driver/passenger front airbags, side airbags, curtain airbags, and seat belt pretensioners) from deploying.

It may also interrupt communication with the powertrain CAN and body CAN, causing the instrument cluster to illuminate the airbag warning lamp continuously.

Unlike sensor or ignition circuit faults, this DTC indicates a functional failure of the ECU itself.

Inspect the ECU installation environment (the area beneath the center tunnel is susceptible to water ingress) and verify power supply stability.

5
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Intermittent SRS ECU fault on BYD Qin EV300 after wading

✓
A 2017 Qin EV300 developed an intermittent airbag light after driving through flood water during heavy rain. Retrieved DTCs: B16C2-00 (current) and U0151 (historical). Inspection found the SRS ECU mounted under the centre tunnel; the housing seal had aged and allowed water ingress, causing verdigris corrosion on the internal PCB. Measured the ECU's internal 5V reference: it dropped to 4.2V hot, starving the acceleration sensor of power. Fix: Replaced the SRS ECU (K2J-5823000-00), resealed the mounting location, added a waterproof gasket beneath the ECU, and performed online configuration. Fault resolved.
BYD DTC AI Analysis

Aftermarket stereo installation on a Qin 100 caused CAN bus interference, triggering an ECU fault.

✓
The owner reported that after installing an aftermarket touchscreen head unit, the airbag warning light stayed on. DTC B16C2-00 was stored, accompanied by multiple U-class communication faults. Technicians found the installation shop had bridged the SRS-CAN and infotainment CAN when tapping the head unit into the bus, causing signal reflection and abnormal voltage (CAN-H reached 4.8V). They removed the improper wiring, restored the factory CAN topology, and cleared the fault codes. The ECU then passed self-diagnosis. Recommendation: Never connect aftermarket devices to the SRS-CAN bus.
BYD DTC AI Analysis

Qin EV450 lost calibration data after collision repair

✓
After a frontal collision, the repair shop replaced the front airbags and impact sensors but did not replace the SRS ECU, as it appeared undamaged externally. After reassembly, the vehicle set code B16C2-00, and the scan tool displayed “Internal Configuration Error”. The ECU had latched collision data during the impact and entered fuse-locked mode, with partial calibration data corruption. Since BYD policy does not support unlocking, the shop replaced the ECU with a new unit. Using VDS, they performed “Online Configuration” to write the VIN and configuration codes (requires connection to the BYD server for authorisation). After completion, the system self-test passed.
BYD DTC AI Analysis

Unstable supply voltage caused ECU reset fault

✓
A BYD Qin 80 with 80,000 km had the airbag warning light illuminate at startup. DTC B16C2-00 was intermittent. Inspection found the battery had aged (increased internal resistance). Voltage dropped to 8.5 V during cranking, triggering the ECU internal undervoltage protection and setting the fault code. The ECU constant power terminal also had a poor connection — resistance measured 2.3 Ω (normal <0.1 Ω). Solution: replaced the battery, repaired the ECU power plug terminals (cleaned and fitted a locking tab), cleared the DTC. Followed up for one week, no recurrence.
BYD DTC AI Analysis

False positive caused by software version bug

✓
Some 2018-batch Qin EV450 vehicles have an ECU software calibration defect. When starting in extreme cold (below -15°C), a timing error in the internal self-diagnostic program falsely triggers B16C2-00. The vehicle has no actual hardware fault. After warm-up, you can clear the code, but it will return. Solution: Use VDS to perform a 'software upgrade' and flash the V2.3.1 calibration file (which fixes the low-temperature self-diagnostic timing). Flashing completely eliminated the fault. This shows that not all B16C2-00 codes require hardware replacement.
Other Seal U Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.