UK
AU
C001C00

DTC C001C00 indicates the IPB (Intelligent Integrated Braking System) ECU detects a fault in the right rear wheel inlet valve (normally open valve) drive circuit — Seal U

Braking System

DTC C001C00 indicates the IPB (Intelligent Integrated Braking System) ECU detects a fault in the right rear wheel inlet valve (normally open valve) drive circuit.

This typically occurs when the internal ECU valve drive circuit (MOSFET or dedicated driver chip) detects an open circuit, short to power, short to ground, or abnormal current feedback while attempting to drive the right rear inlet valve.

The inlet valve acts as a key actuator in the ABS/ESP hydraulic control unit, controlling brake fluid flow from the master cylinder to the right rear wheel cylinder.

This fault prevents the right rear wheel from participating in ABS pressure regulation and ESP active braking intervention.

Extreme cases may affect braking balance; however, the system retains basic hydraulic braking functions (direct pedal pressure build-up).

The warning lamp illuminates, and the system disables functions including ABS, ESP, and Automatic Emergency Braking (AEB).

3
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Open circuit in IPB internal solenoid valve coil caused ABS failure

✓
A 2021 Song PLUS DM-i at 30,000 km had constant ABS and ESP warning lights. VDS read fault code C001C00 (right rear inlet valve driver fault). Freeze frame showed 0 km/h vehicle speed at the time of the fault. The technician disconnected the IPB connector and measured the right rear inlet valve resistance at infinite (open circuit). The left rear inlet valve measured 5.2Ω (normal). This confirmed an open solenoid coil inside the IPB assembly. Replaced the IPB electro-hydraulic module assembly and performed the brake bleed procedure. Cleared the fault codes. ABS function returned to normal.
Original source ↗
BYD DTC AI Analysis

Connector corrosion after water ingress caused intermittent fault

✓
After driving through standing water, the dashboard intermittently displayed "Check Brake System" and DTC C001C00 set sporadically. The IPB wiring harness connector showed obvious water stains and green corrosion inside. Reduced insulation resistance between pins caused the ECU to misdiagnose an actuator fault. Cleaned the connector with electrical contact cleaner, dried it thoroughly, applied BYD conductive grease (or petroleum jelly), and repositioned the waterproof seal. No recurrence after one week of continuous monitoring following reassembly.
BYD DTC AI Analysis

Brake fluid contamination caused valve body sticking and false fault codes

✓
During maintenance, found severely degraded brake fluid (black, water content >4%). ABS warning light then lit up. Read DTC C001C00. Solenoid resistance measured normal, but actuation test showed drive current fluctuating abnormally (0.8A-1.2A unstable; normal is stable ~1.0A). Disassembled IPB for inspection (teaching demo) and found brown deposits jamming the inlet valve spool. IPB is a sealed assembly, so replaced the IPB module and brake fluid. Fault resolved. Advised owner to replace brake fluid every 2 years or 40,000 km.
Other Seal U Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.