AU
B1651-00

This DTC indicates the airbag control unit (SRS ECU) detects the front passenger seat belt pretensioner circuit resistance exceeds the calibrated upper limit (typically >3 — Atto 3

Safety System

This DTC indicates the airbag control unit (SRS ECU) detects the front passenger seat belt pretensioner circuit resistance exceeds the calibrated upper limit (typically >3.5Ω, standard value approximately 2.0Ω±0.4Ω).

Electrically, the pretensioner is essentially a squib consisting of a resistance wire and an igniter charge.

High resistance usually indicates high impedance or an open circuit.

Potential causes include a partially blown internal resistance wire in the pretensioner, increased connector contact resistance, or a hidden open circuit in the wiring harness.

This fault causes the SRS system to enter degraded mode: during a frontal collision, the front passenger seat belt fails to pretension automatically, and the system may suppress the front passenger airbag deployment strategy, severely compromising passive safety performance.

4
Cases Logged
5
Causes
Likely Causes — Atto 3
  • 1Internal aging of the seat belt pretensioner assembly: Long-term vibration or thermal cycling oxidizes and thins the pretensioner igniter resistance wire, causing the resistance value to drift beyond the threshold.
  • 2Poor wiring harness connector contact: Oxidized or loose terminals in the yellow SRS connector under the seat or at the B-pillar (usually beside the front passenger seat rail or inside the lower B-pillar trim), or the shorting bar fails to fully disengage, causing increased contact resistance.
  • 3Floor wiring harness damaged: Vehicle wading, carpet cleaning, or liquid spills in the front passenger footwell cause wiring harness corrosion; frequent fore-and-aft seat adjustment causes wiring harness fatigue and breakage (especially repeated bending when the under-seat wiring harness retaining clip detaches).
  • 4SRS ECU sampling circuit error: Fault in the control unit internal A/D conversion circuit or sampling resistor causes resistance reading deviation (rule out via cross-checking).
  • 5Improper modification or repair: Replacing the front passenger seat with non-genuine parts, or splicing wires when installing a seat heating/ventilation system, causing additional series resistance in the pretensioner circuit or poor contact due to damaged insulation.
What To Do
  • 1
    Safety preparation: Switch the vehicle to OFF, disconnect the 12V battery negative terminal, and wait at least 90 seconds for the SRS capacitor to fully discharge. Wear an anti-static wrist strap and disable wireless communication devices.
  • 2
    Fault Confirmation: Connect the VDS2000 or BYD dedicated diagnostic tool and read the fault code status. Confirm whether B1651-00 is 'Active' or 'History'. If multiple SRS fault codes exist, troubleshoot common power supply and ground issues first.
  • 3
    Physical location: Remove the front passenger seat (4 retaining bolts, torque usually 40-50 N·m) or lower B-pillar trim panel. Locate the yellow-labeled pretensioner wiring harness connector (usually marked F-P/T or PRETENSIONER FR RH).
  • 4
    Offline measurement: Disconnect the pretensioner connector. Use a digital multimeter (low-resistance range, 0.1 Ω accuracy) to measure resistance directly across the two terminals on the pretensioner side. Normal value: 1.6-2.4 Ω. If resistance is >3.0 Ω or infinite, the pretensioner has failed. Replace the seat belt assembly (do not replace the pretensioner separately).
  • 5
    Wiring harness inspection: If pretensioner unit resistance is normal, check connector pins for oxidation or blackening, and female terminals for expansion. Measure continuity on the harness side from the connector to the SRS ECU (located under the center console or in the front compartment); resistance should be <1.0Ω. Thoroughly inspect the under-seat wiring harness for wear within the seat rail movement range.
  • 6
    Insulation check: Use a megohmmeter to measure the insulation resistance between the pretensioner circuit and body ground. The resistance must be >10 MΩ. If the insulation value is low, inspect the wiring harness for chafing and short circuits to the body.
  • 7
    System reset: After repairing or replacing the faulty component, reconnect all connectors (listen for the locking 'click') and reinstall the seat. Connect the battery, switch the ignition ON, use the diagnostic tool to clear the fault code, and perform 'SRS system configuration' (if installing a new component, write the VIN and configuration code).
  • 8
    Function verification: Perform an SRS system self-diagnosis and confirm B1651-00 does not return. Verify the instrument cluster airbag warning light turns off after the 6-second self-check. Use an SRS deployment simulation tool (such as a 10Ω resistor) to verify the ECU sampling circuit operates normally before conducting a vehicle test.
Real-World Cases
BYD DTC AI AnalysisFrom Chinese market (translated)

Qin EV450 front passenger pretensioner high resistance fault following water ingress

✓
A 2018 Qin EV450 had water on the passenger floor from a blocked sunroof drain. After the customer dried the carpet, the airbag warning light stayed on. The retrieved DTC was B1651-00. Inspection found water inside the SRS wiring harness connector under the passenger seat, and the pins had green copper corrosion. After cleaning the connector and applying conductive grease, the pretensioner resistance returned to 2.1 ohms, but the continuity resistance from the harness side to the ECU fluctuated between 0.8 and 2.5 ohms. The copper wires inside the floor wiring harness had corroded and broken at the water accumulation point. Replacing the floor wiring harness resolved the fault. Recommend clearing the sunroof drains to prevent recurrence.
BYD DTC AI AnalysisFrom Chinese market (translated)

Seat modification on Qin 100 caused loose connection in pretensioner circuit

✓
2017 BYD Qin 100. Owner had the front passenger leather electric seat replaced at an outside shop with an aftermarket unit. One week later, DTC B1651-00 set. Inspection found the shop used non-standard crimp terminals when transferring the original seatbelt pretensioner connector, and didn't waterproof them. The pretensioner circuit had about 2.5Ω of contact resistance in series. The shop re-soldered the wiring harness, sealed it with heat shrink tubing, and installed a genuine connector. Resistance returned to normal. Reminder: Seat modifications involving SRS must use genuine wiring harness and terminals. Simple twisting or splicing is strictly prohibited.
BYD DTC AI AnalysisFrom Chinese market (translated)

Intermittent B1651-00 due to seat rail interference

✓
A Qin EV300. The customer reported the airbag warning light would occasionally illuminate, especially after adjusting the front passenger seat forward or backward. DTC B1651-00 was intermittent. Inspection found the wiring harness retaining clip beneath the seat had detached. The seat rail track repeatedly pinched the harness, causing some internal copper strands to fracture while the insulation remained intact, creating high resistance. Repaired the harness, re-secured the clip, and adjusted the wiring slack to provide enough free play at both full-forward and full-rearward seat positions. The fault did not recur. This case shows the importance of securing wiring harnesses.
BYD DTC AI AnalysisFrom Chinese market (translated)

Resistance drift due to pretensioner body aging

✓
2017 BYD Qin 80, 120,000 km, no collision history. DTC B1651-00 set suddenly. Measured resistance at the pretensioner connector: 4.8Ω, too high. Disconnected the connector and measured the pretensioner body directly (requires removing the seatbelt retractor), reading 4.9Ω. Determined to be internal resistor wire aging in the pretensioner. Replaced the passenger side seatbelt assembly (with pretensioner), clearing the fault. Analysis: Long-term high temperatures (vehicle parked outdoors long-term) caused oxidation of the igniter's internal resistor wire. For this type of aging fault, replace the complete assembly directly; do not attempt repair.
Other Atto 3 Fault Codes
P0A0DBattery Energy Control Module Requested MIL IlluminationP0AA6Hybrid Battery Voltage System Isolation FaultP1A00Drive Motor "A" Performance — BYD proprietaryB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself. Sources: [1]