AU
B169B-00

DTC B169B-00 indicates an internal self-diagnostic fault or severe communication error within the airbag control unit (SRS ECU) — Atto 3

Safety System

DTC B169B-00 indicates an internal self-diagnostic fault or severe communication error within the airbag control unit (SRS ECU).

This fault indicates the microprocessor, memory (EEPROM/Flash), power supply monitoring circuit, or watchdog circuit within the SRS ECU detected an abnormality, preventing guaranteed airbag deployment.

When this fault occurs, the SRS ECU enters fail-safe mode, illuminates the airbag warning light, and disables all airbags, seat belt pretensioners, and crash unlock functions, severely compromising passive safety.

This is a Hard Fault; disconnecting the power typically will not clear it.

Repair the power supply or communication wiring, or replace the ECU.

The B169B-00 fault code on the Atto 3 indicates an internal fault or communication error within the airbag control unit (SRS ECU), preventing guaranteed airbag deployment. Severity is medium. Common causes include voltage surges or thermal damage to the ECU circuit board, and abnormal power supply from battery or connection issues. The fix requires visiting an authorised dealer to inspect wiring or replace the unit. Typical repair cost data is available based on 4 recorded cases.
4
Cases Logged
5
Causes
Likely Causes — Atto 3
  • 1SRS ECU internal circuit board damage: Voltage surges (such as reversed polarity during jump-starting or charger surges), long-term thermal cycling causing solder joint cracking, or internal capacitor aging causing power supply filtering failure.
  • 2Abnormal power supply: Prolonged low (<9V) or high (>16V) battery voltage, poor connection in the IGN power circuit, poor fuse contact, or oxidation at ground point G201 (left side of instrument panel) causing reference voltage drift.
  • 3CAN bus communication fault: Short or open circuit in the CAN-H (orange/black) or CAN-L (orange/brown) lines between the SRS ECU, gateway, and vehicle control unit; abnormal terminating resistance (120Ω); or bus voltage out of standard range (CAN-H 2.5-3.5V, CAN-L 1.5-2.5V).
  • 4Software or calibration data corruption: Interrupted flashing, calibration data checksum failure, or physical damage to the Flash memory prevents the ECU from loading the correct airbag deployment algorithm and crash threshold parameters.
  • 5External environmental factors: Water ingress into the SRS ECU from vehicle wading (mounting location below the A/C evaporator box makes it susceptible to moisture); latent micro-damage from a collision; or strong electromagnetic interference (such as high-power radio equipment) causing an abnormal CPU reset.
What To Do
  • 1
    Diagnostic scan: Use VDS2000 or a dedicated BYD diagnostic tool to access the SRS system and read freeze frame data. Confirm whether B169B-00 is an active or history fault. Record vehicle speed, battery voltage, temperature, and other parameters at the time of the fault. Check for accompanying fault codes (such as U-prefix communication faults or B16XX-series sensor faults).
  • 2
    Power and ground check: Turn off the ignition. Measure the voltage to ground at pin 16 (constant power B+) and pin 15 (IGN) of the SRS ECU connector. The voltage must be 11-14V. Measure the resistance between the ground pin (usually pin 14) and the vehicle body. The resistance must be <1Ω. Inspect fuses SB11 (10A, instrument panel power distribution box) and SB15 (15A) for blown elements or poor contact. Check the power supply waveform using an oscilloscope to rule out excessive ripple voltage (>100mV).
  • 3
    CAN bus inspection: Disconnect the SRS ECU connector and measure the resistance between CAN-H and CAN-L (approximately 60Ω, two 120Ω terminating resistors in parallel). Check for short circuits between CAN-H and ground, CAN-L and ground, and CAN-H and CAN-L. Use a CAN analyzer to capture the waveform. Verify the dominant level (CAN-H 3.5V / CAN-L 1.5V) and recessive level (2.5V) are normal, and check for abnormal bit stuffing errors.
  • 4
    ECU inspection: Remove the SRS ECU located under the center console or behind the glove box (exact location varies by model; on Qin series, it typically mounts on the right side of the A/C evaporator housing). Inspect the exterior for water marks, burn marks, cracks, or impact deformation. Measure the output of the ECU internal voltage regulator chip (which normally supplies a 5V reference voltage to the sensors). An abnormal reading confirms internal ECU damage. Note: Never dismantle the ECU housing (due to safety sealing and explosion-proof requirements).
  • 5
    Replacement and matching: If the ECU is faulty, replace it with a new SRS ECU with the same part number (e.g., HA2E-5810000A or specific to the vehicle model). Before installation, disconnect the battery negative terminal for at least 5 minutes. After installation, connect the diagnostic tool and perform 'Online Matching' and 'Coding'. Enter the vehicle VIN and airbag configuration parameters (e.g., side airbag and knee airbag presence). Perform a 'System Self-check' to clear the fault code and simulate an ignition test (use the diagnostic tool to execute the 'Collision Output Test' function; this operation flashes the airbag warning lamp but does not deploy the airbags).
  • 6
    Road test verification: Restore the vehicle, start the vehicle, and confirm the airbag warning lamp turns off after 6 seconds. Conduct a road test over bumpy roads and through turns to confirm the fault code does not recur. Use a diagnostic tool to read the live data stream and verify sensor voltages, crash signal status, and CAN communication status are normal. Inform the customer the SRS system is operating normally and the airbag system was inactive during the repair.
Real-World Cases
BYD DTC AI Analysis

Qin EV450 SRS fault light on after charging

✓
A 2018 BYD Qin EV450 displayed 'Check SRS System' on the instrument cluster after the owner used a non-genuine DC fast charger. Technicians retrieved DTC B169B-00. They found oxidation on the SRS ECU connector. Power supply voltage measurement during fast charging showed a momentary spike to 16.8 V, triggering the ECU's internal overvoltage protection. They replaced the SRS ECU, installed a zener diode protection circuit, and updated the BMS software to limit charging voltage fluctuations. Fault resolved.
BYD DTC AI Analysis

Qin 100 airbag warning light stays on after water ingress.

✓
2017 BYD Qin 100. The vehicle waded through water about 40 cm deep, after which the airbag warning light stayed on. The diagnostic scanner retrieved DTCs B169B-00 and B1650-00 (left impact sensor fault). Disassembly revealed water had entered the SRS ECU mounting location (below the evaporator case) and green corrosion on the circuit board. Replaced the ECU and wiring harness connector, then resealed the area by installing a waterproof cover and applying sealant. Fault resolved. Recommend checking the air conditioning drain hose for blockages.
BYD DTC AI Analysis

ECU communication failure after accident repair

✓
After a front collision repair on a Qin EV300, DTC B169B-00 appeared and could not be cleared. Inspection found the accident deformed the front bulkhead and displaced the SRS ECU mounting bracket, cracking the ECU housing slightly and putting the internal gyroscope sensor out of calibration. The accident also crushed the CAN wiring harness, damaging the insulation and causing an intermittent short circuit. Replaced the SRS ECU, repaired the wiring harness, corrected the installation position, performed online matching, and the fault cleared.
BYD DTC AI Analysis

Software flash failure locked the ECU

✓
During an SRS software upgrade on a Qin 80 at the dealership, the diagnostic tool disconnected, causing the flash to fail and triggering DTC B169B-00. The ECU entered boot mode (flashing protection mode) and could not communicate via standard methods. Using a dedicated programming power supply to maintain stable voltage, the technician accessed engineering mode, re-flashed the underlying software, restored calibration data, and resolved the fault. This case emphasises that a regulated power supply must be used during flashing; power interruption is strictly prohibited.
Other Atto 3 Fault Codes
P0AA6Hybrid Battery Voltage System Isolation FaultB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.B173A1ADTC B173A1A indicates the right middle-row side airbag (typically located on the side of the right second-row seat or inside the C-pillar trim panel) igniter circuit resistance measures 0 Ω. In the Supplemental Restraint System (SRS), normal airbag igniter resistance ranges between 2.0 and 5.0 Ω. A resistance of 0 Ω indicates a short to ground or a short between circuit wires, preventing the Airbag Control Unit (ACU) from establishing a normal monitoring circuit. This safety-critical fault prevents the airbag from deploying during a collision, continuously illuminates the instrument panel SRS warning lamp, and may force the entire airbag system into fail-safe mode.
Common problems reported for Atto 3 →Atto 3 overview →
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.