AU
P060700

DTC P060700 indicates a functional fault in the internal control processor (MCU/ECU) of the IPB (Intelligent Power Brake) — Atto 3

Braking System

DTC P060700 indicates a functional fault in the internal control processor (MCU/ECU) of the IPB (Intelligent Power Brake).

This fault stems from a hardware-level or low-level software abnormality, specifically involving a main control chip calculation error, memory checksum failure, watchdog timeout reset, or internal bus communication interruption.

As a core braking component on BYD e-Platform 3.0 and DM-i models, the IPB integrates ESP, ABS, EBD, energy recovery, and brake assist functions.

This fault causes brake assist failure (hard brake pedal), loss of ESC/ABS functions, and Automatic Emergency Braking (AEB) deactivation.

It may also trigger limp-home mode (speed-limited driving).

When this fault occurs, the IPB enters a safety protection state and defaults to pure hydraulic braking.

This severe fault compromises driving safety.

The P060700 fault code on the Atto 3 indicates an internal processor fault in the Intelligent Power Brake (IPB) system. This medium-severity issue can cause hard brake pedal feel, loss of ABS/ESC, AEB deactivation, or limp-home mode. Common causes include internal IPB ECU hardware failure or unstable power/ground supply. The recommended fix is to visit an authorised dealer for diagnosis and repair. Typical repair cost data is available from recorded cases.
5
Cases Logged
5
Causes
Likely Causes — Atto 3
  • 1Internal ECU hardware damage in the IPB electro-hydraulic module: cold solder joints on the main control chip (Infineon or NXP series), corrupted memory (Flash/EEPROM) data, or peripheral circuit component failure (capacitors, crystal oscillators). Batch hardware defects or long-term vibration commonly cause these failures.
  • 2Power supply system fault: Unstable voltage (below 9V or above 16V) in the IPB power supply circuit (constant power B+, ignition IG1), loose or oxidized ground terminals, or insufficient battery charge causing abnormal processor reset.
  • 3Software operation fault: A bug in the IPB control software version (e.g., early Song PLUS DM-i V1.2) causes excessive CPU load or memory overflow under specific operating conditions (e.g., frequent energy recovery switching + emergency braking).
  • 4Electromagnetic interference (EMI): Electromagnetic pulses generated by high-power radio equipment, non-OEM electrical accessories, or damaged high-voltage wiring harness shielding disrupt CAN communication or processor clock signals.
  • 5Wiring harness connector fault: Backed-out pins, corrosion due to water ingress, or excessive contact resistance at the IPB module 32-pin connector (especially power pins 1-4 and ground pins 5-8), causing momentary interruption of the processor power supply.
What To Do
  • 1
    Initial diagnostic scan: Use the BYD VDS2000/VDS3000 to read all DTCs and confirm if P060700 is a current fault (Active). Check for accompanying fault codes (e.g., U1000 communication fault, C1234 brake pressure sensor fault). Record freeze frame data (vehicle speed, brake pressure, and voltage values when the fault occurred).
  • 2
    Power supply and ground check: Disconnect the IPB module connector. Measure voltage at pin 1 (terminal 30, constant power) and pin 2 (terminal 15, ignition power) (standard: 12.6 ± 0.3 V). Check ground resistance at pins 5-8 (must be less than 1 Ω). Use an oscilloscope to monitor voltage drop during vehicle start to confirm if it falls below 9 V and triggers the fault.
  • 3
    Communication bus inspection: Measure CAN-H (pin 9) and CAN-L (pin 10) voltage to ground (2.5V±0.1V) and terminal resistance (60Ω±5Ω). Check the CAN waveform for distortion or noise to rule out electromagnetic interference.
  • 4
    Software update attempt: If hardware checks are normal, use VDS to update the IPB module software (latest version V2.1 or higher). Before updating, back up calibration data for the steering angle sensor, brake pressure sensor, etc. After updating, clear the DTCs and perform a 30-minute road test.
  • 5
    Assembly replacement and adaptation: If the fault persists, replace the IPB electro-hydraulic assembly (part number: SC-3630100-B1). After replacement, perform the following: ① Brake system bleeding (requires a dedicated fluid bleeding tool); ② Steering angle sensor calibration (G85); ③ Longitudinal/lateral acceleration sensor calibration; ④ Brake pressure sensor zero-point calibration; ⑤ AEB function road test verification.
  • 6
    In-depth verification: Perform a 20km road test, including an ABS activation test (hard braking at 40km/h), an energy recovery test (coasting in B gear), and limp mode verification. Confirm the fault code does not recur and all warning lights are off.
Real-World Cases
BYD DTC AI Analysis

Cold solder joint on Song Plus DM-i IPB main board causes intermittent fault

✓
2021 Song PLUS DM-i, 23,000 km. Dashboard intermittently lit the ABS/ESC warning light; DTC P060700 set intermittently. Fault frequency higher during cold starts. Diagnosis revealed dry solder joints on the main control chip (Infineon TC397) on the PCB inside the IPB module; thermal expansion caused poor contact. Replaced the IPB assembly, bled the brake lines and calibrated the sensors on the new module. No recurrence after three months.
BYD DTC AI Analysis

Aftermarket dash cam installation caused electromagnetic interference fault

✓
Non-OEM dashcam installed (constant power tap), power line routed parallel to IPB supply. P060700 set intermittently while driving with U1000 communication fault. Testing found the dashcam had poor power filtering, generating high-frequency interference that coupled into the IPB processor through the wiring. Rewired to maintain >30cm from high-voltage harness, installed ferrite core filter, and updated IPB software to the interference-hardened version.
BYD DTC AI Analysis

Software bug triggered processor overload

✓
Drove on highway using ACC heavily (follow-brake-accelerate cycles). After one hour, P060700 set and brake assist failed. Diagnosis: Early software version (V1.15) triggered watchdog reset when CPU load exceeded 95% during frequent switching between regenerative and mechanical braking. Fix: Upgraded IPB software to V2.05, optimizing the brake energy recovery algorithm to reduce processor load.
BYD DTC AI Analysis

Battery aging triggered low voltage fault

✓
Battery was 3 years old and never replaced. During cold winter cranking, voltage dropped to 8.2V, triggering P060700 that would not clear. Measured voltage waveform at the IPB power supply terminal during cranking and found an 8V undervoltage pulse lasting 10ms, causing an abnormal processor reset. Solution: Replaced the AGM battery (12V 60Ah) and cleaned the IPB ground terminal (G106); fault cleared.
BYD DTC AI Analysis

IPB internal short circuit and corrosion after water ingress

✓
After driving through water exceeding half the tire height, the brake system warning light on the instrument panel remained illuminated and DTC P060700 set. Removal and inspection of the IPB module revealed deterioration of the electro-hydraulic control unit seal, allowing coolant (or rainwater) to enter the ECU housing. This short-circuited the main board electrolytic capacitors and burned out the processor power supply chip. Solution: Replaced the IPB assembly, checked the waterproof sealing of related wiring harness connectors, and replaced the brake fluid (moisture content exceeded specification).
Other Atto 3 Fault Codes
P0AA6Hybrid Battery Voltage System Isolation FaultB1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.B173A1ADTC B173A1A indicates the right middle-row side airbag (typically located on the side of the right second-row seat or inside the C-pillar trim panel) igniter circuit resistance measures 0 Ω. In the Supplemental Restraint System (SRS), normal airbag igniter resistance ranges between 2.0 and 5.0 Ω. A resistance of 0 Ω indicates a short to ground or a short between circuit wires, preventing the Airbag Control Unit (ACU) from establishing a normal monitoring circuit. This safety-critical fault prevents the airbag from deploying during a collision, continuously illuminates the instrument panel SRS warning lamp, and may force the entire airbag system into fail-safe mode.
Common problems reported for Atto 3 →Atto 3 overview →
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.