AU
B1705-00

This DTC indicates the Supplemental Restraint System (SRS) detects a short to ground in the left curtain airbag deployment circuit — Atto 8

Safety System

This DTC indicates the Supplemental Restraint System (SRS) detects a short to ground in the left curtain airbag deployment circuit.

Specifically, during self-diagnostics or monitoring, the SRS control module (ACU) detects insulation resistance between the left curtain airbag igniter circuit and vehicle ground (GND) below the system threshold (typically <2Ω).

This causes abnormal current leakage to ground instead of normal flow through the airbag deployment circuit.

This fault may result in: 1) the left curtain airbag failing to deploy normally in a collision, compromising head protection for front and rear left occupants; 2) the SRS entering fail-safe mode, disabling related airbag functions, and illuminating the instrument cluster airbag warning light; 3) unintended airbag deployment in extreme cases due to abnormal circuit heating.

The fault involves the left curtain airbag module, wiring harness, connectors, or internal SRS control module circuits.

The B1705-00 fault code on the Atto 8 indicates a high-severity short to ground in the left curtain airbag deployment circuit. This can stop the left curtain airbag from deploying correctly and may turn on the airbag warning light. Common causes include damaged or pinched wiring in the pillar/headliner area, or water ingress and corrosion at the connector. Visit an authorised dealer for diagnosis and repair. Typical repair cost data is available from recorded cases.
5
Cases Logged
5
Causes
Likely Causes — Atto 8
  • 1Left curtain airbag wiring harness worn or pinched: Inside the A-pillar, B-pillar, or C-pillar trim panels, the wiring harness rubs against the body metal frame, seat mounting bracket, or roof reinforcement, damaging the insulation and causing the conductor to directly contact body ground.
  • 2Connector water ingress or corrosion: Vehicle wading, a blocked sunroof drain tube, or poor body sealing causes water to enter the left curtain airbag connector (usually located in the left body side panel, headliner, or C-pillar trim), forming a conductive path between terminals or producing verdigris.
  • 3Curtain airbag module internal fault: Abnormal drop in inflator internal igniter resistance (below 1.0Ω) or internal short circuit, causing resistance to ground to fall outside standard specifications (typical standard value: 2.0±0.1Ω).
  • 4SRS control module (ACU) internal drive circuit fault: Internal ignition drive transistor breakdown or monitoring circuit fault causing a false short circuit detection or actual output short circuit.
  • 5Improper accident repair: During collision repair, missing left curtain airbag wiring harness retaining clips, incorrect harness routing contacting sharp edges, or use of non-original specification connectors resulting in poor sealing.
What To Do
  • 1
    Safety preparation and system discharge: Park the vehicle in a safe area, apply the parking brake, turn the ignition switch to OFF, disconnect the 12V battery negative terminal, and wait at least 90 seconds to fully discharge the SRS system energy storage capacitor and prevent accidental airbag deployment.
  • 2
    Fault Confirmation and Data Recording: Use a BYD VDS2000 or Launch X431 diagnostic tool to read the fault code. Confirm B1705-00 is a Current fault, not a History fault. Record the Freeze Frame Data, including parameters such as vehicle speed and temperature when the fault occurred.
  • 3
    Visual inspection and wiring harness check: Remove the left A-pillar upper trim panel, B-pillar upper trim panel, left headliner trim panel, and C-pillar trim panel. Inspect the left curtain airbag wiring harness for wear, cuts, or burn marks. Verify the wiring harness protective sleeve is intact near the seat rails, seat belt mounting points, and body sheet metal holes. Inspect the connector for looseness, water ingress, corroded pins, or backed-out terminals.
  • 4
    Circuit test and isolation diagnosis: Disconnect the SRS control module and left curtain airbag module connectors. Use a multimeter to measure the resistance between the ignition circuit terminals on the harness-side connector and body ground (standard value: >10MΩ), and measure continuity between the harness terminals (must be continuous with resistance <1Ω). If the harness is normal, connect a 2Ω special resistor to the SRS control module in place of the curtain airbag module. If the fault code clears and does not return, the curtain airbag module is faulty.
  • 5
    Component replacement and repair: Based on diagnostic results, replace the left curtain airbag assembly (Note: The airbag module is a single-use component. Replace the complete unit if deployed or if resistance is abnormal. Do not repair internal structures), repair the damaged wiring harness (wrap with waterproof insulating tape or replace the wiring harness assembly), or clean or replace corroded connectors.
  • 6
    System reset and functional verification: Reconnect all connectors. Verify the connectors lock fully and the waterproof sealing rings seat correctly. Install all interior trim panels. Connect the battery negative terminal. Clear fault codes using the diagnostic tool. Perform the SRS system self-test (typically requires cycling the ignition switch 3 times). Verify DTC B1705-00 does not return. Check that the instrument panel airbag warning light turns off normally after the self-test (normal operation: the light illuminates during the self-test and turns off after 6 seconds).
Real-World Cases
BYD DTC AI Analysis

Song MAX driver seat backrest rearward adjustment inoperative

✓
Symptoms: The instrument cluster showed a seat adjustment system fault. The driver’s seat could not electrically adjust the backrest angle, the seat memory function failed, and the cluster displayed a “Check Seat System” warning. Diagnosis: The technician scanned with a VDS diagnostic tool and retrieved DTC B1705-00 (Driver Seat Back Rearward Adjustment Switch Circuit Fault). Inspected the under‑seat harness connector – secure, no looseness. Removed the seat side switch panel, measured resistance of the backrest rearward adjustment switch, and found an internal open circuit (normally should be closed). Checked the harness from the switch to the seat control module; continuity was normal, no shorts or opens. Solution: Replaced the driver seat switch assembly (includes backrest forward and rearward adjustment switches). Cleared the DTC and test‑drove the vehicle. All electric seat adjustment functions returned to normal and the DTC did not return. Note: On Song MAX models, DTC B1705‑00 indicates a seat switch circuit fault.
Original source ↗
BYD DTC AI Analysis

Qin Pro DM seat back rearward adjustment intermittently inoperative

✓
Symptoms: BYD Qin Pro DM. The owner reported the driver's seat backrest adjustment button was inoperative; there was no response when adjusting rearward, while forward adjustment worked normally. After powering on the vehicle, the instrument cluster occasionally displayed a seat system fault warning. Diagnosis: At the shop, technicians used the BYD dedicated diagnostic tool to retrieve fault codes, which showed B1705-00 (driver's seat backrest rearward switch circuit fault). They removed the seat side trim panel and inspected the switch connector, finding no oxidation or corrosion. Using a multimeter on the switch signal wire, they detected no voltage change when pressing the rearward adjustment switch (normally a 12V or 5V signal change should occur). They further disassembled the switch and found burned internal contacts and poor connection. Solution: Since the individual switch component was unavailable, technicians replaced the entire seat adjustment switch panel assembly and re-matched the seat memory function, resolving the fault. After clearing the B1705-00 fault code, it did not return. This fault code is related to the seat system in the Qin Pro DM.
Original source ↗
BYD DTC AI Analysis

Tang petrol: Seat backrest rearward adjustment inoperative, accompanied by abnormal relay noise

✓
Symptoms: BYD Tang petrol variant, 32,000 km. The driver reported the power seat backrest adjustment failed — it moved forward but not backward. When using the switch, a relay clicked but the motor did not run. Diagnosis: Scanned with a Launch X431 and retrieved DTC B1705-00 from either the Body Control Module (BCM) or seat control module. The technician first suspected a defective motor or mechanical binding. Powered the backrest adjustment motor directly and it ran normally. Checked the switch signal and found the rearward adjustment signal did not reach the control module. Tested the switch itself and found oxidised internal contacts interrupting the signal. Resolution: Cleaning the switch contacts was ineffective. Replaced the driver's seat eight-way adjustment switch assembly. Cleared the fault code. The seat backrest now adjusts in both directions. A three-month follow-up confirmed no recurrence.
Original source ↗
BYD DTC AI Analysis

Han EV Genesis Edition seat adjustment fault related to temperature and humidity

✓
Symptoms: BYD Han EV Founders Edition. After 6 months from new, the driver's seat backrest rearward adjustment began to fail intermittently. The fault occurred more frequently in hot weather and occasionally worked normally when cold. Diagnostic process: The dealership technician received the vehicle and confirmed the fault after multiple test drives. VDS scan retrieved historic DTC B1705-00. Inspected the seat wiring harness routing and identified a risk of interference and chafing near the seat rails. Removed and inspected the switch; found slight moisture traces on the internal PCB, suspected to be related to HVAC condensation or humid conditions. Measured the switch insulation resistance, which was below specification. Solution: Replaced the seat adjustment switch assembly. Fitted protective sleeving to the wiring harness at wear-prone areas and adjusted the routing to prevent interference with moving components. Fault eliminated after the repair.
Original source ↗
BYD DTC AI Analysis

Atto 3 seatback adjustment failed after an aftermarket seat ventilation installation.

✓
Symptoms: BYD Yuan Plus. After the owner modified the seat ventilation, the driver’s seat backrest rearward adjustment failed, though other directions worked normally. The instrument cluster showed no warning lights, but the seat memory function could not save positions. Diagnosis: The workshop first scanned the vehicle with a diagnostic tool and found DTC B1705-00 stored in the seat control module. The shop asked the owner and learned the seat had been removed during the modification. Inspecting the switch plug revealed that while drilling holes for the ventilation fan, the technician had accidentally damaged the wiring harness for the backrest rearward adjustment switch with the drill bit. This caused the signal wire to break internally while the insulation remained visually intact. Solution: Repaired the damaged wiring harness (reconnected the broken signal wire and applied insulation and waterproofing). After clearing the fault codes, all seat functions returned to normal. Advised the owner to choose a professional workshop for future seat modifications.
Original source ↗
Other Atto 8 Fault Codes
B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110A02DTC B110A02 indicates the thermal management master control unit (HVAC ECU) or body control module (BCM) failed to receive valid CAN data frames from the PM2.5 air quality sensor over consecutive communication cycles (typically 500ms per cycle). The sensor typically mounts at the HVAC unit air inlet or behind the glove box and transmits real-time particulate concentration data (unit: μg/m³) to the HVAC controller via the CAN bus. The fault is essentially a communication link layer timeout. Potential causes include physical layer wiring faults, sensor power supply failures, sensor internal MCU lockup, or CAN network topology damage. Although this non-critical fault does not directly affect driving safety, it disables the intelligent air purification strategy and the automatic fresh air/recirculation switching function. In extreme cases, it triggers a thermal management system degraded mode, limiting compressor power or fixing the air flap position.B110B07This fault code indicates abnormal operation of the internal air pump (sampling pump) in the PM2.5 air quality detection module. The PM2.5 detector uses the laser scattering principle to measure particulate concentration and requires a built-in air pump to draw ambient air into the detection chamber at a constant flow rate. The ECU sets this code when it detects an open or short in the air pump drive circuit, abnormal current (stall or free-running), or abnormal speed feedback. This fault causes the automatic air conditioning system to lose air quality sensing capability, preventing automatic switching between fresh air and recirculation modes. The instrument cluster air quality display may show '--' or a fixed value, but the fault does not affect the vehicle powertrain or basic air conditioning cooling and heating functions.B173CDTC B173C indicates the Supplemental Restraint System (SRS) detects the Right Second Row Side Airbag squib circuit resistance exceeds the calibrated threshold (typically >4.5Ω). This fault is an active diagnostic result of the SRS system, indicating a high-resistance condition in the circuit between the Airbag Control Unit (ACU) and the airbag module. Causes for excessive resistance include increased contact resistance, a partially broken wiring harness, terminal oxidation, or an aging squib wire inside the airbag module. This fault causes the system to mark the airbag circuit as 'unreliable', meaning the airbag may fail to deploy during a collision. The fault typically illuminates the instrument cluster airbag warning light (SRS light) continuously, and some models also sound a warning buzzer.
Common problems reported for Atto 8 →Atto 8 overview →
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.