AU
B172D12

In DTC B172D12, "B" indicates the Body/Safety system, "172D" identifies the Left Middle Row Side Airbag, and "12" indicates a Short to B+ — Atto 8

Safety System

In DTC B172D12, "B" indicates the Body/Safety system, "172D" identifies the Left Middle Row Side Airbag, and "12" indicates a Short to B+.

This fault indicates the airbag control unit (SRS ECU) detects abnormal continuity between the Left Middle Row Side Airbag squib circuit and the vehicle power supply (12V).

Under normal conditions, the airbag squib resistance is approximately 1.5-3.0Ω.

The SRS ECU monitors circuit current and voltage through the low-side or high-side driver circuit.

When the ECU detects circuit voltage continuously exceeding the threshold (typically >5V and approaching battery voltage), it identifies a short to B+.

This fault prevents normal airbag deployment (causing failure to deploy or unintended deployment during a collision).

As a hard fault, it triggers a continuous SRS warning light, forces the system into fail-safe mode, and disables the affected airbag function.

4
Cases Logged
5
Causes
Likely Causes — Atto 8
  • 1Wiring harness wear near the seat slide rail: Forward and backward adjustment of the left middle-row seat causes the airbag wiring harness to rub against the seat frame or slide rail edge. Prolonged friction damages the insulation, allowing internal wires to contact a power wire (such as the seat heating supply or a constant power wire) and cause a short circuit.
  • 2Airbag module connector fault: Backed-out connector terminals, oxidation from water ingress, or bent pins shorting the squib terminal to the power supply terminal. Common after vehicle wading or washing.
  • 3Airbag squib internal short circuit: Insulation breakdown of the gas generator squib inside the airbag module shorts the resistance wire to the housing (excluding ground) or power supply. Internal module quality issues or previous impact damage usually cause this.
  • 4Improper SRS wiring harness modification or accident repair: installing aftermarket seat ventilation/heating equipment pierces the airbag wiring harness, or improperly securing the harness after accident repairs causes seat bolts or metal brackets to pinch the harness.
  • 5SRS control unit internal driver chip fault: Breakdown of the ECU internal squib driver transistor causes the output terminal to remain high, triggering a false external short circuit detection (uncommon but requires inspection).
What To Do
  • 1
    Safety preparation: Turn off the ignition, disconnect the low-voltage battery negative terminal, and wait at least 90 seconds to fully discharge the SRS capacitor and prevent accidental airbag deployment.
  • 2
    Fault Confirmation: Connect the BYD VDS diagnostic tool. Read the complete DTC information and freeze frame data (record vehicle speed, temperature, etc., at the time of the fault). Confirm B172D12 is a current fault (Active), not a history fault.
  • 3
    Visual inspection: Remove the left middle-row seat (or left B-pillar lower trim panel, depending on vehicle configuration) and inspect the airbag module connector (usually located under the seat or near the C-pillar) for looseness, water ingress, corrosion, or obvious damage.
  • 4
    Circuit test: Disconnect the airbag module connector and use a multimeter to measure the voltage to ground at the harness-side (vehicle-side) connector terminal. Normal voltage is 0-1V (low-side drive) or close to 0V; if the multimeter reads 12V, confirm a short to power.
  • 5
    Harness inspection: Follow the airbag harness routing (typically under the seat, along the B-pillar, and through the floor harness channel) and check the insulation for damage. Inspect the seat mounting bolts, seat rail edges, and harness retaining clips for signs of pinching or abrasion.
  • 6
    Isolation test: If the wiring harness appears normal, disconnect the SRS ECU connector and measure the insulation resistance between the airbag wiring harness and the power wire. Resistance must be greater than 10MΩ. If the resistance is too low, strip the harness in sections to locate the short circuit.
  • 7
    Component verification: If the wiring harness is normal, measure the airbag module resistance (1.5-3.0 Ω). If the resistance is abnormal (<1 Ω or >5 Ω) or a continuity test indicates a short to the housing, replace the left middle-row side airbag module.
  • 8
    Repair Verification: After repairing the wiring harness (replacing the damaged section or rewrapping) or replacing the module, reconnect all connectors and the battery. Use VDS to clear the fault code. Perform the 'SRS System Self-Diagnosis' and 'Output Test'. Confirm B172D12 does not return and the warning lamp turns off.
Real-World Cases
BYD DTC AI Analysis

BYD E2 seat rail wear caused wiring harness short to power.

✓
Model: 2019 BYD E2 EV Symptom: SRS warning light stays on. VDS read DTC B172D12. Diagnosis: Removed left middle row seat. The wiring harness under the seat was completely worn through at the rear mounting point of the slide rail. Internal copper wire was in direct contact with the seat heating power wire (red 12V). Cause: Harness retaining clip had come off; long-term forward/backward seat adjustment caused the wear. Solution: Repaired the damaged harness (cut and re-soldered with heat-shrink tubing), rerouted the harness, added corrugated tubing for protection, and adjusted the retaining clip position to avoid interference with moving parts.
BYD DTC AI Analysis

Water ingress caused short circuit in Qin EV left-second-row side airbag connector.

✓
Model: 2019 Qin EV. Symptoms: SRS warning light illuminates after rain or car washing, DTC B172D12 appears intermittently. Diagnosis: Inspected the airbag connector beneath the seat. Found a deteriorated seal ring, with water stains and green copper corrosion inside the terminals. Resistance between the igniter terminal and constant power terminal measured 0.5 Ω, indicating a short circuit. Cause: Water entered the connector due to vehicle wading or high-pressure floor washing. Solution: Cleaned the connector terminals thoroughly with electronic cleaner and compressed air. Replaced the waterproof seal ring, applied electrical contact protectant, and replaced the wiring harness connector assembly where necessary.
BYD DTC AI Analysis

E3 aftermarket seat modification pinched the airbag wiring harness, causing a short circuit

✓
Model: 2020 BYD E3. Symptoms: B172D12 DTC appeared one week after leather seat replacement. Diagnosis: Checked beneath the new seat and found the SRS wiring harness trapped between the seat mounting bolt and floor during the modification. Tightening the bolt cut through the harness insulation, causing a short circuit between the core wire and the seat heater power supply line. Cause: The unauthorised workshop failed to route the SRS wiring harness correctly when installing the seats. Solution: Repaired the damaged harness (replaced the entire section to ensure safety), rerouted according to factory layout, and ensured sufficient clearance (>20mm) between the harness and metal edges.
BYD DTC AI Analysis

SRS control unit false report caused B172D12 fault

✓
Vehicle: 2019 Qin EV. Symptoms: No accident history or modifications. Intermittent DTC B172D12. When the fault occurred, harness voltage was normal. Diagnosis: Disconnected the airbag module, connected a dedicated airbag simulator (2Ω resistor) to the circuit; the fault persisted. Measured the ECU output terminal and found the internal drive circuit outputting an abnormal 12V. Cause: SRS ECU internal squib driver chip failure (batch quality issue). Solution: Replace the airbag control unit (requires programming and matching, plus vehicle configuration writing and impact sensor calibration).
Other Atto 8 Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.