AU
B176B1A

DTC B176B1A indicates the left rear seat belt pretensioner circuit resistance falls below the standard threshold set by the SRS control unit (ACU) (typically 1 — Qin Plus

Safety System

DTC B176B1A indicates the left rear seat belt pretensioner circuit resistance falls below the standard threshold set by the SRS control unit (ACU) (typically 1.5–3.0 Ω; the fault triggers below the lower limit).

This is an SRS hard fault, indicating a potential or actual short circuit in the pretensioner igniter circuit.

As a key passive safety system actuator, the pretensioner uses electrical current to trigger the igniter.

This ignites the gas generator to tighten the seat belt during a collision (within approximately 15–20 ms).

Low resistance may cause: 1) Unintended deployment (static electricity or electromagnetic interference causing accidental ignition); 2) The ACU to disable this trigger circuit in fail-safe mode, preventing seat belt pretensioning during a collision; 3) The ACU to lock out the entire SRS system if resistance drops near 0 Ω, disrupting the multi-airbag coordinated deployment strategy.

4
Cases Logged
5
Causes
Likely Causes — Qin Plus
  • 1Pretensioner igniter internal short circuit: Moisture ingress, electrolyte corrosion, or manufacturing defects cause the insulation between the igniter bridge wire and the housing to break down, forming a low-resistance path.
  • 2Harness short to ground: Seat adjustment, crushing by objects, or water ingress damages the insulation of the left rear sill harness (B-pillar to C-pillar section), shorting the wire to the body ground.
  • 3Connector terminal fault: Short circuit between terminals in the yellow SRS connector under the seat (usually near the left rear seat rail) caused by water ingress, oxidation, or mechanical damage.
  • 4ACU internal sampling circuit fault: A damaged shunt resistor or A/D converter inside the airbag control unit causes a false low resistance reading.
  • 5Parallel aftermarket equipment: Incorrectly connecting unauthorized seat heaters, massagers, or child seat anchorage devices in parallel to the SRS circuit decreases total resistance.
What To Do
  • 1
    Safety preparation: Disconnect the battery negative terminal and wait at least 3 minutes to fully discharge the ACU capacitor. Remove the left rear seat for access.
  • 2
    Visual inspection: Check the left rear seat belt pretensioner connector (yellow) for looseness, water ingress, or corrosion; check the wiring harness inside the B-pillar trim for pinching or damage.
  • 3
    Resistance measurement: Disconnect the ACU and pretensioner connectors. Use a digital multimeter (resistance setting) to directly measure the resistance between the two pretensioner terminals. Standard value: 2.0±0.3Ω. If <1.5Ω, replace the pretensioner.
  • 4
    Insulation check: Measure the resistance between either pretensioner terminal and body ground. Resistance must be infinite (>1MΩ). If continuity exists, inspect the wiring harness for damaged insulation shorting to ground.
  • 5
    Harness continuity test: Measure harness continuity between the ACU terminal and the pretensioner connector, and check for a short to ground. If necessary, use an oscilloscope to check for abnormal capacitive coupling.
  • 6
    Replacement verification: If measured values are normal but the fault persists, replace the pretensioner assembly with a known good unit, or connect a dummy resistor (2.2Ω) to the ACU terminals to determine if the pretensioner or the ACU sampling circuit is faulty.
  • 7
    System reset: After repair, reconnect all connectors and turn on the power. Use VDS or a dedicated diagnostic tool to clear the fault code. Perform the 'SRS System Configuration' and 'Pretensioner Resistance Learning' procedures (if applicable).
  • 8
    Function verification: Perform a static test (ignition switch ON, instrument cluster self-check) and a dynamic test (simulate a collision signal and observe resistance value stability in the data stream). Confirm the fault code does not return.
Real-World Cases
BYD DTC AI Analysis

Water ingress under left rear seat caused pretensioner short circuit

✓
2019 BYD Qin PRO DM. Owner reported the airbag warning light stayed on constantly. Read DTC B176B1A. Inspection found the left rear carpet damp. Disassembly revealed obvious water stains inside the yellow 2-pin SRS connector under the left rear seat; electrolytic corrosion caused a micro-short between terminals, measuring 0.8Ω. Cause: The left rear door seal had deteriorated, allowing rainwater to seep in and accumulate at the lowest point of the seat rail. Replaced the left rear seatbelt pretensioner assembly (including retractor), treated the corroded terminals in the wiring harness, replaced the door seal, and dried the cabin. No recurrence in three months of follow-up.
BYD DTC AI Analysis

Aftermarket heated seats caused impedance anomaly

✓
2018 Qin PRO petrol. B176B1A set within one week of aftermarket rear seat heater installation at a non-authorized workshop. Technicians found the installer had spliced the heating pad power feed into the seatbelt pretensioner harness in parallel, dropping total SRS circuit resistance to 1.2Ω. The ACU detected resistance deviation exceeding 25% and triggered the fault code. Repair: Removed the unauthorized harness, repaired original wiring insulation with double-layer heat shrink tubing, and restored factory connectors. Explained to the customer that the SRS system strictly prohibits parallel loads; recommended an independent power supply for seat heating.
BYD DTC AI Analysis

ACU internal sampling resistor drift causes false fault

✓
A Qin PRO DM with 60,000 km showed intermittent B176B1A faults. Left rear pretensioner resistance measured 2.1Ω (normal) and harness insulation was good, yet the fault triggered on rough roads. Oscilloscope monitoring revealed abnormal voltage fluctuations at the ACU sampling terminal. After replacing the ACU (airbag control unit), the fault disappeared. The reference resistor in the Analog Front End (AFE) chip had drifted from thermal cycling, shifting the sampling reference for the left rear channel. When hardware tests normal but the fault code keeps returning, suspect the ACU itself.
BYD DTC AI Analysis

B-pillar wiring harness chafed, short to ground

✓
2019 Qin Pro set DTC B176B1A after accident repairs (left rear door replacement). Inspection found the B-pillar trim panel was installed with the harness improperly secured. The seatbelt pretensioner wiring (yellow corrugated tubing) was pinched between the door outer panel and B-pillar reinforcement. Repeated door closing vibrations chafed through the insulation, exposing the copper core and creating a low-resistance path to ground (measured 12Ω). Repair: Cut out the damaged section, soldered in an extension, and applied double insulation. Rerouted and secured the harness per standard wiring paths, ensuring >20mm clearance from sharp edges. Fault resolved.
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.