AU
C001D00

This DTC indicates a drive circuit fault for the Right Rear Outlet Valve inside the Intelligent Integrated Braking System (IPB) electro-hydraulic module — Qin Plus

Braking System

This DTC indicates a drive circuit fault for the Right Rear Outlet Valve inside the Intelligent Integrated Braking System (IPB) electro-hydraulic module.

The outlet valve is a key actuator in the ABS/ESP hydraulic modulator.

During the pressure reduction phase, it routes brake fluid from the right rear wheel cylinder back to the reservoir to reduce wheel cylinder pressure.

A drive fault typically indicates the ECU detected an open or short circuit in the solenoid valve coil, abnormal drive current, or a damaged power stage circuit (MOSFET/driver chip).

This fault disables the right rear wheel ABS/ESP pressure reduction function and forces the system into a degraded protection mode (ABS/ESC functions limited or disabled).

Symptoms include a hard brake pedal, increased braking distance, and, in extreme cases, compromised vehicle stability control.

The C001D00 fault code on the Qin Plus indicates a medium-severity drive circuit fault in the right rear outlet valve of the IPB braking module. This can limit or disable ABS/ESC pressure reduction at the right rear wheel, increasing braking distance or affecting stability. Common causes include a failed outlet valve solenoid coil or a damaged IPB control board driver circuit. Visit an authorised dealer for diagnosis and repair. Typical repair cost data is available.
3
Cases Logged
5
Causes
Likely Causes — Qin Plus
  • 1Open circuit or inter-turn short circuit in the right rear outlet valve solenoid coil inside the IPB electro-hydraulic module, causing drive current to exceed the threshold range.
  • 2IPB control board power drive circuit fault, such as damaged intelligent high-side/low-side switch chip, shorted driver MOSFET, or abnormal sampling resistor.
  • 3Mechanical binding in the hydraulic valve body (contamination, corrosion, or seal ring debris) causes excessive resistance to solenoid valve movement, creating a continuously high drive current that triggers protection.
  • 4Poor contact in the IPB module low-voltage power supply or ground circuit causes the drive voltage to drop, preventing the generation of sufficient electromagnetic force to drive the valve spool.
  • 5IPB control software fault or calibration parameter drift causing incorrect valve drive timing or improper diagnostic threshold settings (intermittent false alarms)
What To Do
  • 1
    Use the BYD VDS or a dedicated diagnostic tool to read all DTCs, confirm C001D00 is an active fault, and record freeze frame data (vehicle speed, brake pressure, voltage, etc.).
  • 2
    Visually inspect the IPB electro-hydraulic module and verify no impact damage, brake fluid leaks, or signs of corrosion or water ingress at the connector. Check the continuity and insulation of the related wiring harnesses (power, ground, CAN).
  • 3
    Perform the IPB actuator self-test (Actuator Test) and listen for a clear clicking sound from the right rear outlet valve. If no sound occurs or the diagnostic tool indicates a drive failure, confirm an internal fault.
  • 4
    Measure the resistance between the right rear outlet valve drive pin and the internal coil at the IPB connector (normal: approx. 2-8 Ω). If the resistance is infinite (open circuit) or close to 0 Ω (short circuit), this indicates an internal solenoid valve fault.
  • 5
    Upon confirming an internal IPB fault, replace the IPB electro-hydraulic module assembly with ECU (the part number must match the vehicle model; for example, Song PLUS DM-i requires the corresponding hardware version).
  • 6
    After replacement, perform the complete repair procedure: bleed the brake lines (requires dedicated bleeding equipment or a diagnostic tool to activate the pump motor), calibrate the yaw rate sensor, calibrate the longitudinal acceleration sensor, perform IPB function self-learning, and verify with a road test.
Real-World Cases
BYD DTC AI Analysis

Song PLUS DM-i IPB Internal Solenoid Short Circuit Replacement Case

✓
Vehicle mileage 28,000 km. ABS and ESP warning lights lit up suddenly while driving; the instrument panel displayed "Check Brake System." VDS found C001D00 (current fault) and C001C04 (right rear inlet valve fault). Inspected the IPB connector: no abnormalities. Measured resistance at the right rear valve body drive pins: only 0.8Ω (severe short circuit). Disassembled the IPB: internal PCB driver chip burnt, hydraulic valve body coil insulation damaged. Replaced the IPB assembly, performed brake bleeding and sensor calibration. Fault resolved.
BYD DTC AI Analysis

IPB Right Rear Valve Body Drive Fault Repair After Water Ingress

✓
After driving through standing water, multiple brake system warning lights came on. The scan tool showed C001D00 and multiple wheel speed sensor faults. Inspection found water pooling beneath the IPB mounting location; the connector seal had aged, allowing moisture ingress. Cleaning and drying the connector did not clear C001D00. Further testing revealed moisture had penetrated the IPB internals, corroding the right rear outlet valve drive circuit open. Replaced the IPB assembly and improved waterproofing at the mounting location to resolve the fault.
BYD DTC AI Analysis

IPB software refresh resolved intermittent outlet valve driver fault

✓
Intermittent ABS warning light reported; cleared on restart. Scanner read C001D00 as a history fault with current status normal. Wiring harness, connectors, and power supply checked normal. Solenoid valve resistance within range. Root cause: IPB control software falsely flagged a drive fault under specific conditions (low-voltage cranking or transient electromagnetic interference). Flashed IPB ECU to the latest software version, cleared fault codes post-flash. Monitored for one month; no recurrence.
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110BDTC B110B indicates a fault in the internal air pump (sampling pump) of the PM2.5 air quality detector. This pump draws cabin or outside air into the PM2.5 sensor detection chamber, enabling the laser scattering sensor to measure real-time particulate matter concentration. The air conditioning controller (or BCM) sets this DTC upon detecting an open or short circuit in the pump drive circuit, or abnormal current caused by a seized pump motor. This fault disables the "Green Clean" system, causes the instrument cluster air quality display to read abnormally or disappear, and disables the automatic fresh air/recirculation switching function. It does not affect the vehicle powertrain or core thermal management functions.B173A1ADTC B173A1A indicates the right middle-row side airbag (typically located on the side of the right second-row seat or inside the C-pillar trim panel) igniter circuit resistance measures 0 Ω. In the Supplemental Restraint System (SRS), normal airbag igniter resistance ranges between 2.0 and 5.0 Ω. A resistance of 0 Ω indicates a short to ground or a short between circuit wires, preventing the Airbag Control Unit (ACU) from establishing a normal monitoring circuit. This safety-critical fault prevents the airbag from deploying during a collision, continuously illuminates the instrument panel SRS warning lamp, and may force the entire airbag system into fail-safe mode.B173BDTC B173B indicates an abnormal electric A/C compressor speed feedback signal or a communication fault between the compressor controller and the motor. In BYD new energy models (e.g., Tang, Song, Qin, and Yuan series), this DTC belongs to the HVAC subsystem within the Body Control system and specifically involves the electric compressor closed-loop control circuit. The ECU sets this DTC when the compressor controller (IPM) fails to receive a valid pulse signal from the Hall speed sensor for more than 3 continuous seconds, or when the deviation between the detected actual speed and the target commanded speed exceeds the calibrated threshold (typically >500 rpm). This fault forces the A/C system into fail-safe mode and stops compressor operation. Symptoms include a complete lack of cooling, intermittent cooling, or a sharp decrease in cooling performance. The instrument cluster A/C warning lamp may also illuminate. Prolonged operation with this fault can degrade high-voltage system insulation or cause controller overcurrent damage.
Common problems reported for Qin Plus →Qin Plus overview →
Data confidence: Official This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.