UK
AU
C12F909

DTC C12F909 indicates a blockage or abnormal flow in the internal hydraulic circuit of the IPB (Intelligent Integrated Braking) system — Qin Plus

Braking System

DTC C12F909 indicates a blockage or abnormal flow in the internal hydraulic circuit of the IPB (Intelligent Integrated Braking) system.

The IPB system integrates the traditional vacuum booster with the ESP and uses a motor-driven hydraulic unit to provide brake boost.

The ECU sets this fault when it detects an abnormal pressure difference between the master cylinder and the wheel cylinders, hydraulic pump current exceeding the threshold, or solenoid valve flow deviating from the calibrated value.

Potential causes include a blocked brake fluid passage, a sticking solenoid valve, hydraulic pump wear, or internal seal failure.

When this fault occurs, the IPB enters a degraded mode that retains basic hydraulic braking but disables energy recovery and automatic emergency braking.

Extreme cases may cause a hard brake pedal or increased braking distance.

4
Cases Logged
Real-World Cases
BYD DTC AI Analysis

Degraded brake fluid caused valve body sticking in Song PLUS DM-i

✓
Vehicle mileage: 42,000 km. Instrument cluster displayed "Brake System Fault." Retrieved DTC C12F909. Inspection revealed dark brown brake fluid with 4.2% moisture content. Removed and inspected the IPB module; found black gummy deposits on the inlet valve spool surface. Thoroughly cleaned the hydraulic unit internal passages, installed fresh DOT4 brake fluid, and performed three bleed cycles. Fault cleared. Advised the owner to replace the brake fluid every 2 years or 40,000 km.
BYD DTC AI Analysis

Water ingress caused internal IPB short circuit, triggering circuit fault

✓
The vehicle drove through water deeper than the wheel hubs. The next day, C12F909 appeared with the ABS warning light illuminated. Disassembled the IPB module and found the motor connector seal had perished. Water had penetrated, allowing brush wear debris to contaminate the hydraulic fluid. Replaced the IPB assembly and flushed all brake lines with alcohol before drying them. The fault has not reoccurred.
BYD DTC AI Analysis

False blockage from failure to bleed brakes after brake fluid change

✓
C12F909 appeared after brake fluid replacement at a non-authorised workshop. The technician only performed manual pedal bleeding. The VDS automatic bleed procedure revealed a large amount of air bubbles in the right rear wheel cylinder bleed passage. After completing the standard automatic bleed, master cylinder pressure response time recovered from 1200ms to 650ms and the fault code cleared automatically.
BYD DTC AI Analysis

Aged IPB master cylinder seal causing internal leak

✓
2021 BYD Song PLUS DM-i, 60,000 km. Intermittent C12F909 on cold start. Data analysis showed pressure drop rate >3 MPa/s during the pressure-holding phase. Disassembled the IPB and found the master cylinder piston seal hardened and cracked, allowing high-pressure brake fluid to leak to the reservoir through the return port. The ECU misdiagnosed this as a circuit blockage. Replaced the IPB assembly; fault resolved.
Other Qin Plus Fault Codes
B1108For the BYD Song MAX (2017–2019), DTC B1108 indicates a short circuit in the PM2.5 air quality detection module (dust sensor) or its wiring harness. The sensor uses laser scattering to detect in-cabin and outside PM2.5 concentrations and transmits data to the HVAC ECU via the LIN bus or an analog signal. Short circuit conditions include: 1) Sensor power supply wire (+5V/+12V) shorted to ground 2) Signal wire shorted to power or ground 3) Short circuit in the sensor's internal photoelectric detection circuit This fault prevents the automatic climate control from switching between fresh air and recirculation based on air quality. The system enters fail-safe mode (typically forced recirculation). Severe short-circuit current can destroy the HVAC ECU sampling circuit. The system classifies this as a Level 3 severe fault and restricts vehicle operation to prevent electrical fires or controller damage. For other BYD models (such as the Qin EV, E5, and Song DM), B1108 indicates a driver-side sunload sensor fault, reflecting differences in DTC definitions across models.B110811This DTC indicates a short circuit in the air conditioning system PM2.5 air quality sensor (rapid detector). Specifically, abnormal continuity exists between the sensor power supply circuit or signal output circuit and body ground or battery positive. This causes the control module (ACU/air conditioning controller) to detect abnormal current or a voltage signal outside the valid range (typically 0V or supply voltage). The PM2.5 sensor monitors internal and external particulate concentrations, providing the data the automatic air conditioning system uses to switch between fresh air and recirculation modes. A short circuit disables the air quality monitoring function. This fault may force the air conditioning system into recirculation protection mode and trigger related thermal management system faults, as the air conditioning system acts as a key actuator in vehicle thermal management. In severe cases, the short circuit current can damage the internal sampling circuit of the air conditioning controller or overheat the wiring harness.B1109DTC B1109 indicates an open circuit in the communication line between the air conditioning system PM2.5 air quality sensor (dust concentration sensor) and the air conditioning control unit (AC ECU), or an open circuit within the sensor internal circuitry. Typically located in the air conditioning intake duct, this sensor monitors real-time PM2.5 particle concentration inside and outside the vehicle. It provides data to the automatic air conditioning system for intelligent switching between fresh air and recirculation modes and for controlling the air purification device. During an open circuit fault, the AC ECU cannot receive the air quality signal, triggering the system fail-safe mode. Symptoms typically include failure of the automatic recirculation function, abnormal air purification indicator light operation, or abnormal air quality data displayed on the air conditioning panel. Severe cases may compromise the cabin environment control strategy, but do not directly affect vehicle driving safety.B110913DTC B110913 indicates an open signal circuit for the PM2.5 rapid detector (in-cabin air quality sensor). This sensor typically mounts inside the air conditioning system intake duct. It monitors in-cabin PM2.5 concentration in real time and provides data to the automatic air conditioning system for intelligent control of the air purification function. The BYD diagnostic protocol uses sub-code '13' to specifically indicate an open signal circuit. Although this fault theoretically affects a comfort feature, BYD Qin series vehicles classify it as a Level 3 (severe) fault. This classification occurs because the air conditioning system interacts with the battery thermal management system (e.g., monitoring battery cooling intake air quality). The fault can disable the automatic air conditioning mode and prevent the air purification function from operating. In extreme cases, it affects the battery compartment intake air quality assessment, triggering the 'repair immediately' strategy.B110AThis DTC indicates interrupted CAN bus communication or abnormal data between the air conditioning control unit (ACU) and the PM2.5 air quality sensor. The PM2.5 sensor monitors particulate concentration inside and outside the vehicle and provides the basis for purification control in the automatic air conditioning system. The ACU triggers this fault if it fails to receive a valid CAN message from the sensor within the specified period (usually 100-500 ms), if message verification fails, or if the signal frame times out. Although this fault does not affect vehicle driving safety, it disables the automatic air purification function. The air conditioning system cannot automatically switch between recirculation and fresh air modes or activate the air purification mode based on air quality. A persistent fault may restrict the thermal management strategy.
Data confidence: Community This information is for reference only. Always consult a qualified technician for diagnosis and repair. Do not attempt high-voltage system repairs yourself.